1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas，liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital
Preferred and Alternative Methods for Estimating Air Emissions from
Feb 29, 2012 Natural gas boilers are considered clean relative to coal- or oil-fired boilers, but improper levels and flue gas recirculation also often lower NOx emissions. . Testing and Materials (ASTM) standard methods referred to as
Continuous Flue Gas Flow Calculation in the New Standard EN ISO
gas volumetric flow rate based on the European boiler performance standard EN . some plant, the flue gas flow velocity profile can be very asymmetric and
Characterization of residential chimney conditions for flue gas flow
The flow velocities in residential chimneys from a heating boiler under normal operating condi- sors, as significant temperature gradients may be present in flue gas ducts. .. However, the standards do not readily provide methods for tak-.
BOILER EFFICIENCY GUIDE - Cleaver-Brooks
for optimum flue gas velocities in the achieve optimal flue gas velocity, which . standard. Firetube boiler designs are available using as little as four square
Properly Designing a Boiler Exhaust System - Cleaver-Brooks
Mar 21, 2012 boiler/economizer/feedwater system, economizer installations can impact the selection of suitable proper flue gas velocity in the vertical exhaust. Drainage minimum air intake area as specified in the local standards. 8.
P l D i i Properly Designing A Boiler Exhaust System - Cleaver-Brooks
Boilers are divided into four categories based on the pressure and Flue gas velocity calculation heating appliances which vent flue gases at a temperature not . ASME STS-1 2011: Steel Stacks- http://www.asme.org/kb/standards.
Flue Gas Analysis in Industry
To meet these limit values combustion plants are equipped with flue gas cleaning systems such . for the standard operational conditions of the plant. . Condensing boilers are boilers that make use of the condensation heat of the flue gas added . use of a very high gas flow velocity in the sample lines, as developed and.
Combustion Booklet (PDF) - E Instruments
measured. The EPA has set specific standards and regulations for emissions of some of remaining in the flue gas, the closer to complete combustion the reaction becomes. working conditions but also maximize the boilers efficiency. .. mass emissions is based on the velocity of the gases being sent out of the stack, the.
Impact of Chimneytop Appurtenances on Flue Gas Flow
sources of such information are standards and codes, as well as reports of research Keywords: appurtenances, chimney-top, draft, flue, gas flow, testing . In certain solid fuel boilers, the chimney height should be more .. Chimney gas velocity is effective on piping friction factor, KL, and roughness correction factor. .